Ghost Immobiliser Fitting
Protect your vehicle from theft of keys hacking, cloning, and theft with the first aftermarket immobiliser for CAN. The Ghost app and GPS tracking can be linked to the immobiliser to send you alerts when your vehicle is stolen or tampered with.
Installing a Ghost immobiliser is a breeze for a skilled technician. It is important to have the appropriate tools and heat shrink tubing.
Getting Started
In what is ghost immobiliser to physical security devices like wheel locks and car alarms, ghost immobilisers safeguard your vehicle without the use of LEDs or key fobs. They are directly connected to the ECU CAN data network and are activated only after entering a PIN. This provides a higher level of protection against key hacking, ECU swapping and cloning.
Installing a ghost immobiliser Birmingham requires a certain amount of agility and accuracy. It can be a bit like tiptoeing through an icy minefield. One mistake could cause severe damage to the circuits of the electrical system of your vehicle. To avoid this, it's crucial that you know the procedure for installing and prepare your vehicle accordingly.
You will need to remove interior panels from the vehicle to make space for the immobiliser. Once you've found the perfect place to hide it, use cable tie to secure it. Then, tidy your wiring by making sure that loose wires are tied down and using insulation tape to cover any exposed connections. This will reduce the risk of a short circuit that is not intended to happen, while improving the aesthetics and reducing the risk of theft.
Identify a constant source of 12V power, as well as a grounding source for the ghost immobiliser. Once you have found them, test the power cables using a multimeter. Connect the CAN H & the CAN L wires from the immobiliser to the grounding and power points.
Once you've made all of the necessary connections, it's important to double-check them and inspect the immobiliser for signs of corrosion or damage. Also, test the system to ensure it's functioning properly by entering a pin code and then starting the engine. This should be a regular part of your routine, because it will allow you to detect any issues that might be intermittent early on. Regular testing also helps to improve the longevity of the device and ensure that it is functioning at its best.
Preparing your vehicle
Installing a Ghost immobiliser requires knowledge and tools. A wiring diagram of the vehicle is crucial to identify the proper wires and making precise connections, while a multimeter can be used to verify the electrical value and ensure safety. Cable tie and insulation tape can be used to secure the connections and prevent alteration. A user manual is available for your Ghost Immobiliser. It will give you specific instructions that are tailored to your model.
Once installed, a ghost immobiliser can stop unauthorised engine starts by requiring that the owner input a unique PIN code sequence through existing buttons in the steering wheel or on the centre console. The code can be altered at any time by the vehicle owner by hand or remotely via an app for mobile devices. The device is also quiet and unnoticeable by thieves because it doesn't emit any radio frequency.
A ghost immobiliser is connected directly to the vehicle's CAN bus, which is a network that communicates with all the vehicle's electronic control units (ECUs). It intercepts signals sent by the ECUs and stops the engine from starting when a false signal is detected. The system is weatherproof and tamper proof. It doesn't have any LED indicators or keys to draw the attention of thieves.
It can be positioned behind or in a more obscure area so that it's not obvious to thieves and won't hinder vehicle performance. It could even be placed in a small box, making it less likely to be discovered during a test drive by unscrupulous salespeople selling cars.
Its stealthy operation, along with its integration into the vehicle's CAN-bus system can be an effective deterrent to car theft methods like signal relay attacks and key copying. The system can be integrated with other security measures to create a formidable barrier that can thwart even the most obstinate thieves. A growing number of insurance companies suggest or require ghost immobilisers because they can lower monthly premiums.
Making the Connections
Ghost immobilisers are completely silent, unlike traditional security systems, which can be heard by thieves. They prevent them from knowing that your car is running. They also prevent high-tech methods of theft, like OBD hacking. Installing them without leaving permanent marks on your car is an ideal alternative for those planning to sell the car in the near-future.
The Autowatch Ghost 2 CANbus immobiliser is one of the latest and most reliable options to stop car theft. It disables your engine using the CAN data network and creates a unique PIN code which is difficult to steal from criminals. It can be used on a wide range of vehicles, and it works with many features already installed, such as car alarms, steering wheel locks, GPS trackers and door lock bypass.
If you decide to install a Ghost immobiliser for your vehicle, be sure you refer to the wiring diagram to determine the wires that connect. Double-check the locations of these wires to ensure that they are in the correct location and mark them using tape or labels to make it easier to keep the track of them. It is also necessary to locate a constant power source (12V) for the system as well as an earthing. Once these are in place, you can begin to connect the components to complete the installation.
When the ghost immobiliser is connected to your CAN bus, it will block your vehicle from starting until you enter a pin code using the buttons on the dashboard or the steering wheel. This will stop ECU hacking or key cloning and other techniques of vehicle theft. It can also be paired with other Thatcham approved security devices such as alarms or tyre clips to give your vehicle an even greater degree of security.
As the UK automotive aftermarket industry continues to grow and expand, so are the options for securing your vehicle. With so many avenues for thieves to get in and take your car it's essential to do all you can to ensure it isn't taken away. Ghost immobilisers are a popular choice among car owners who are responsible.
Testing the System
The Ghost Immobiliser uses a CAN data network to communicate with the vehicle's ECU which stops the engine from starting until a specific PIN code is entered. This makes it difficult for thieves copy your key fob to start your vehicle, and harder to disable the system through hacking its electronic.
Ghost Immobilisers can also be used in conjunction with GPS tracking devices to help locate your vehicle in the event that it's stolen. This isn't a common option for aftermarket security solutions however it's a great method to enhance your security and provide peace of mind knowing that your vehicle is always secure.
In addition to providing increased security and security, in addition to providing enhanced security, the Ghost-II immobiliser also provides a comfortable user experience by eliminating the requirement for additional key fobs or devices. It has an easy and simple PIN code entry system that integrates seamlessly into your everyday routine. It also offers convenience features and deactivation settings that allow you temporarily disable the immobiliser in order to park or service your vehicle.
Before beginning the installation process, familiarize yourself with the vehicle's wiring and prepare the necessary tools. A basic set of hand tools will provide you with the flexibility to create precise connections, and a multimeter is a great tool to determine electrical values. Insulation tape and heat-shrink tubing are vital to safeguard connections from short circuits. Cable ties can also be used to secure wiring. It is also essential to work in an area which is well-lit and wear protective gear when working with electrical equipment and components.
You should test the Ghost immobiliser once you have completed the installation to make sure it's functioning properly. Try to start the car without entering the PIN. If this doesn't work then you'll have to retest and inspect the connections more carefully.
Unlike other security systems that are available, unlike other security systems, the Ghost Immobiliser is a covert device that is not spotted by thieves and is far more effective than traditional physical deterrents like wheel clamps or steering locks. It is TASSA-approved, and recognized by some insurance companies. This makes it a cost effective investment that will give you the peace of mind you deserve.